Room-Temperature Carbon Monoxide Detection Using Decorated CNT/Ag Sheet Gas Sensors
DOI:
https://doi.org/10.18321/ectj1694Keywords:
Gas sensing, CO adsorption, CNT/Ag sheet, Conductivity, Schottky barrierAbstract
This work presents the development of a carbon nanotube/silver (CNT/Ag) sheet gas sensor designed for rapid and reliable carbon monoxide (CO) monitoring. The sensing platform is based on conductive carbon nanotube sheets functionalized with silver (Ag) nanoparticles to form a hybrid nanostructured network with enhanced surface activity and electrical transport properties. Surface treatment methods were employed to improve nanoparticle dispersion, interfacial adhesion, and charge transfer between the CNT matrix and Ag nanophase. The sensing mechanism relies on changes in the electrical resistance of the CNT/Ag sheet upon exposure to CO gas. Adsorption of CO molecules on the Ag nanoparticle surfaces alters local electron density and modulates charge transport pathways within the interconnected CNT network, producing a measurable electrical response. Sensor performance was evaluated using a four-point probe configuration at room temperature, demonstrating quantitative detection capability without the need for elevated operating temperatures. The CNT/Ag sheet sensor exhibited reasonable sensitivity, fast response and recovery behavior, and stable operation under ambient conditions. The flexible sheet architecture, combined with the intrinsic conductivity of CNTs and catalytic activity of Ag nanoparticles, provides a lightweight and scalable sensing platform suitable for portable environmental monitoring, industrial safety systems, and smart wearable technologies. These results highlight the potential of CNT/Ag hybrid materials as next-generation gas sensors for efficient and low-energy gas detection capability.
References
(1) R.W. Byard, Carbon monoxide–the silent killer, Forensic Sci. Med. Pathol. 15 (2019) 1–2. Crossref
(2) M. Moberg, E. Hamilton, S. Zeng, et al., Global, regional, and national mortality due to unintentional carbon monoxide poisoning, 2000–2021: results from the Global Burden of Disease Study 2021, The Lancet Public Health 8 (2023) e839–e849. Crossref
(3) H. Kinoshita, H. Türkan, S. Vucinic, et al., Carbon monoxide poisoning, Toxicol. Rep. 7 (2020) 169–173. Crossref
(4) N.B. Hampson, Carbon monoxide poisoning mortality in the United States from 2015–2021. Clin. Toxicol. 61 (2023) 483–491. Crossref
(5) C. Mattiuzzi, G. Lippi, Worldwide epidemiology of carbon monoxide poisoning, Hum. Exp. Toxicol. 39 (2020) 387–392. Crossref
(6) T. Nandy, R.A. Coutu Jr, C. Ababei, Carbon monoxide sensing technologies for next-generation cyber-physical systems, Sensors 18 (2018) 3443. Crossref
(7) Y. Tang, Y. Zhao, H. Liu, Room-temperature semiconductor gas sensors: challenges and opportunities, ACS Sens. 7 (2022) 3582–3597. Crossref
(8) S. You, G. Li, Z. Fan, et al., Nanotechnology-assisted sensors for the detection of carbon monoxide: A review, Int. J. Electrochem. Sci. 18 (2023) 100314. Crossref
(9) S. Uma, M. Shobana, Metal oxide semiconductor gas sensors in clinical diagnosis and environmental monitoring, Sens. Actuators A: Phys. 349 (2023) 114044. Crossref
(10) Y. Xie, Z. Zhang, F. Meng, et al., Strategies and challenges for improving the performance of two-dimensional materials-based gas sensors. Adv. Phys.: X 9 (2024) 2288353. Crossref
(11) J.-K. Ko, I.-H. Park, K. Hong, K.C. Kwon, Recent advances in chemoresistive gas sensors using two-dimensional materials, Nanomaterials 14 (2024) 1397. Crossref
(12) H.R. Ansari, A. Mirzaei, H. Shokrollahi, et al., Flexible/wearable resistive gas sensors based on 2D materials, J. Mater. Chem. C 11 (2023) 6528–6549. Crossref
(13) Y. Shen, Y. Wei, Ch. Zhu, et al., Ratiometric fluorescent signals-driven smartphone-based portable sensors for onsite visual detection of food contaminants, Coord. Chem. Rev. 458 (2022) 214442. Crossref
(14) S. Wei, Z. Li, K. Murugappan, et al., A self‐powered portable nanowire array gas sensor for dynamic NO2 monitoring at room temperature, Adv. Mater. 35 (2023) 2207199. Crossref
(15) L. Wang, J. Song, C. Yu, Recent progress on mass-sensitive gas sensors for environmental and industrial applications, Measurement 249 (2025) 117039. Crossref
(16) D. Wang, M. Xu, D. Zhang, et al., Multifunctional QCM sensor based on UIO-66-NH2/V2CTx MXene films for detection of formaldehyde gas and respiratory behavior, Sens. Actuators B: Chem. 447 (2025) 138804. Crossref
(17) S. Dahiya, N. Yadav, H.K. Singh, et al., Thickness dependent NO2 gas sensing properties of sputtered grown nanostructured TiO2 thin films. Appl. Phys. A 132 (2026) 51. Crossref
(18) S. Hussain, Z. Miao, Y. Han, Highly efficient V2O5@ In2O3 nanoflowers for outstanding NO2 gas sensing proficiencies, Microchem. J. 223 (2026) 117359. Crossref
(19) K.S. Ibrahim, Carbon nanotubes properties and applications: a review, Carbon Lett. 14 (2013) 131–144. Crossref
(20) I. Raya, H.H. Kzar, Z.H. Mahmoud, et al., A review of gas sensors based on carbon nanomaterial, Carbon Lett. 32 (2022) 339–364. Crossref
(21) R. Maheswaran, B.P. Shanmugavel, A critical review of the role of carbon nanotubes in the progress of next-generation electronic applications, J. Electron. Mater. 51 (2022) 2786–2800. Crossref
(22) Z. Mansurov, Synthesis of Carbon Nanomaterials in Flames, Eurasian Chem.-Technol. J. 13 (2011) 5–16. Crossref
(23) M. Sajid, M. Asif, N. Baig, et al., Carbon nanotubes-based adsorbents: Properties, functionalization, interaction mechanisms, and applications in water purification. J. Water Process Eng. 47 (2022) 102815. Crossref
(24) S. Sharifi, R. Shohan, M.A. Hobosyan, et al., Carbon-based nanocomposite yarns reinforced with titanium carbide formed by internally reacted titanium and graphene, MRS Commun. 14 (2024) 190–195. Crossref
(25) B. Kumanek, D. Janas, Thermal conductivity of carbon nanotube networks: A review, J. Mater. Sci. 54 (2019) 7397–7427. Crossref
(26) M. Zhang, K.R. Atkinson, R.H. Baughman, Multifunctional carbon nanotube yarns by downsizing an ancient technology, Science 306 (2004) 1358–1361. Crossref
(27) M.D. Lima, S. Fang, R.H. Baughman, et al., Biscrolling nanotube sheets and functional guests into yarns, Science 331 (2011) 51–55. Crossref
(28) R. Rohilla, J. Prakash, K. Dasgupta, Review of carbon nanotube/graphene nanosheet chemiresistive gas sensors, ACS Appl. Nano Mater. 8 (2025) 23414–23465. Crossref
(29) S.S. Katta, S. Yadav, A.P. Singh, et al., Investigation of pristine and B/N/Pt/Au/Pd doped single-walled carbon nanotube as phosgene gas sensor: A first-principles analysis. Appl. Surf. Sci. 588 (2022) 152989. Crossref
(30) F. Liu, M. Xiao, Y. Ning, et al., Toward practical gas sensing with rapid recovery semiconducting carbon nanotube film sensors, Sci. China Inf. Sci., 65 (2022) 162402. Crossref
(31) W.T. Chong, S.M. Lam, T.-M. Don, et al., Improved photocatalytic activity of zinc oxide through the formation of novel ternary tungsten trioxide/carbon nanotube/zinc oxide composite photocatalyst, Mater. Sci. Eng. B 297 (2023) 116774. Crossref
(32) V. Amrute, K. Bhunia, S.K. Koroth, et al., Large enhancement in humidity sensing performance and photocatalytic efficiency of Ag-doped ZnO/GO nanocomposites, Sci. Rep. 16 (2026) 18432. Crossref
(33) J. Yang, M. Zhang, Y. Zhang, et al., Density functional theory study of adsorption and dissociation of CH2Cl2 on the surfaces of transition metal (Fe, Co, Ni, and Cu)-doped carbon nanotubes. Chem. Phys. Impact 8 (2024) 100437. Crossref
(34) M. Patrignani, J. Juan, O. Nagel, et al., The adsorption of CO and NO on (8, 0) SWCNT decorated with transition metals: a DFT study as a possible gas sensor, Powder Technol. 438 (2024) 119691. Crossref
(35) P. Raju, Q. Li, Semiconductor materials and devices for gas sensors, J. Electrochem. Soc. 169 (2022) 057518. Crossref
(36) L.-Y. Zhu, L.X. Ou, L.W. Mao, et al., Advances in noble metal-decorated metal oxide nanomaterials for chemiresistive gas sensors: overview, Nano-Micro Lett. 15 (2023) 89. Crossref
(37) S. Navale, M. Shahbaz, A. Mirzaei, et al., Effect of Ag addition on the gas-sensing properties of nanostructured resistive-based gas sensors: an overview, Sensors 21 (2021) 6454. Crossref
(38) Y. Wang, Y. Cui, X. Meng, et al., A gas sensor based on Ag-modified ZnO flower-like microspheres: Temperature-modulated dual selectivity to CO and CH4, Surf. Interfaces 24 (2021) 101110. Crossref
(39) S.-J. Young, Y.-H. Liu, Z.-D. Lin, et al., Multi-walled carbon nanotubes decorated with silver nanoparticles for acetone gas sensing at room temperature, J. Electrochem. Soc. 167 (2020) 167519. Crossref
(40) B. Wu, Y. Kuang, X. Zhang, J. Chen, et al., Noble metal nanoparticles/carbon nanotubes nanohybrids: synthesis and applications, Nano Today 6 (2011) 75–90. Crossref
(41) I. Sharafeldin, S. Garcia-Rios, N. Ahmed, et al., Metal-decorated carbon nanotubes-based sensor array for simultaneous detection of toxic gases. J. Environ. Chem. Eng. 9 (2021) 104534. Crossref
(42) R. Shoukat, M.I. Khan, Carbon nanotubes: a review on properties, synthesis methods and applications in micro and nanotechnology, Microsyst. Technol. 27 (2021) 4183–4192. Crossref
(43) H. Beitollahi, F. Movahedifar, S. Tajik, S. Jahani, A review on the effects of introducing CNTs in the modification process of electrochemical sensors. Electroanalysis 31 (2019) 1195–1203. Crossref
(44) M. Hobosyan, P.M. Martinez, A.A. Zakhidov et al., Laminar composite structures for high power actuators, Appl. Phys. Lett. 110 (2017) 203101. Crossref
(45) U. Lamichhane, G.C. Dannangoda, M.A. Hobosyan, et al., Twisted laminar superconducting composite: MgB2 embedded carbon nanotube yarns, Bull. Mater. Sci. 44 (2021) 285. Crossref
(46) T.A. Saleh, The influence of treatment temperature on the acidity of MWCNT oxidized by HNO3 or a mixture of HNO3/H2SO4, Appl. Surf. Sci. 257 (2011) 7746–7751. Crossref
(47) H. Zhang, R. Srinivasan, A systematic review of air quality sensors, guidelines, and measurement studies for indoor air quality management, Sustainability 12 (2020) 9045. Crossref
(48) OSSILA. How to Measure Sheet Resistance using a Four-Point Probe. 2026; Available from: URL
(49) P.K. Panigrahi, B. Chandu, N. Puvvada, Recent advances in nanostructured materials for application as gas sensors, ACS Omega 9 (2024) 3092–3122. Crossref
(50) X. Zhang, W. Lu, G. Zhou, Q. Li, et al., Understanding the mechanical and conductive properties of carbon nanotube fibers for smart electronics. Adv. Mater. 32 (2020) 1902028. Crossref
(51) O.A. Gurova, V.E. Arhipov, V.O. Koroteev, et al., Purification of single‐walled carbon nanotubes using acid treatment and magnetic separation, Phys. Status Solidi B 256 (2019) 1800742. Crossref
(52) G. Wu, X. Yang, J. Dong, Radial breathinglike mode of the collapsed single-walled carbon nanotube bundle under hydrostatic pressure, Appl. Phys. Lett. 88 (2006) 223114. Crossref
(53) P. Giri, D.K. Singh. Possible role of defects in the visible photoluminescence from single walled and multiwalled carbon nanotubes, Mater. Res. Soc. Symp. Proc. 1018 (2007) EE07-03.
(54) M. Jerigová, M. Odziomek, N. López-Salas, “We are here!” oxygen functional groups in carbons for electrochemical applications, ACS Omega 7 (2022) 11544–11554. Crossref
(55) L.T.M. Hoa, Characterization of multi-walled carbon nanotubes functionalized by a mixture of HNO3/H2SO4. Diam. Relat. Mater. 89 (2018) 43–51. Crossref
(56) L.S. De Bortoli, R. de Farias, D.Z. Mezalira, et al., Functionalized carbon nanotubes for 3D-printed PLA-nanocomposites: Effects on thermal and mechanical properties, Mater. Today Commun. 31 (2022) 103402. Crossref
(57) N. Sezer, M. Koç, Oxidative acid treatment of carbon nanotubes, Surf. Interfaces 14 (2019) 1–8. Crossref
(58) P. Szroeder, P. Ziółkowski, I. Sahalianov, et al., The hydroxylated carbon nanotubes as the hole oxidation system in electrocatalysis, Materials 17 (2024) 3532. Crossref
(59) R.D. Bengalli, G. Zerbi, A. Lucotti, et al., Carbon nanotubes: structural defects as stressors inducing lung cell toxicity, Chem.-Biol. Interact. 382 (2023) 110613. Crossref
(60) H. Heise, R. Kuckuk, A.K. Ojha, et al., Characterisation of carbonaceous materials using Raman spectroscopy: a comparison of carbon nanotube filters, single‐and multi‐walled nanotubes, graphitised porous carbon and graphite, J. Raman Spectrosc. 40 (2009) 344–353. Crossref
(61) Z.K. Horastani, S.J. Hajiani, DFT study of Ag-X (X= Pd, Pt, Ag) decorated (8, 0) single wall carbon nanotube for spintronic applications, J. Alloys Compd. 968 (2023) 172231. Crossref
(62) J. Kong, N.R. Franklin, G. Zhou, et al., Nanotube molecular wires as chemical sensors, Science 287 (2000) 622–625. Crossref
(63) E. Snow, F.K. Perkins, E.J. Houser, et al., Chemical detection with a single-walled carbon nanotube capacitor, Science 307 (2005) 1942–1945. Crossref
(64) M. Penza, R. Rossi, M. Alvisi, E. Serra, Metal-modified and vertically aligned carbon nanotube sensors array for landfill gas monitoring applications. Nanotechnology 21 (2010) 105501. Crossref
(65) S. Mahajan, S. Jagtap, Metal-oxide semiconductors for carbon monoxide (CO) gas sensing: A review. Appl. Mater. Today 18 (2020) 100483. Crossref
Downloads
Published
How to Cite
Issue
Section
